HP ProLiant MicroServerのFreeBSD 9.1-RELEASE dmesg
参考に、HP ProLiant MicroServerをFreeBSD 9.1-RELEASEで動かしたときのdmesgを載せておく。
全てのデバイスは適切に認識されて、動作してる。NICはbgeで、options=c019b
SSDを接続したSATAポートは、光学ドライブ用のため150MB/sで動作してるけど、体感的に問題ないのでそのままにしてる。非公式BIOSを書き込めば、300MB/s動作させられるらしい。
Copyright (c) 1992-2012 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD is a registered trademark of The FreeBSD Foundation. FreeBSD 9.1-RELEASE #0 r243825: Tue Dec 4 09:23:10 UTC 2012 root@farrell.cse.buffalo.edu:/usr/obj/usr/src/sys/GENERIC amd64 CPU: AMD Turion(tm) II Neo N40L Dual-Core Processor (1497.55-MHz K8-class CPU) Origin = "AuthenticAMD" Id = 0x100f63 Family = 10 Model = 6 Stepping = 3 Features=0x178bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2,HTT> Features2=0x802009<SSE3,MON,CX16,POPCNT> AMD Features=0xee500800<SYSCALL,NX,MMX+,FFXSR,Page1GB,RDTSCP,LM,3DNow!+,3DNow!> AMD Features2=0x837ff<LAHF,CMP,SVM,ExtAPIC,CR8,ABM,SSE4A,MAS,Prefetch,OSVW,IBS,SKINIT,WDT,NodeId> TSC: P-state invariant real memory = 8589934592 (8192 MB) avail memory = 8111689728 (7735 MB) Event timer "LAPIC" quality 400 ACPI APIC Table: <HP ProLiant> FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs FreeBSD/SMP: 1 package(s) x 2 core(s) cpu0 (BSP): APIC ID: 0 cpu1 (AP): APIC ID: 1 ioapic0 <Version 2.1> irqs 0-23 on motherboard kbd1 at kbdmux0 acpi0: <HP ProLiant> on motherboard acpi0: Power Button (fixed) acpi0: reservation of fee00000, 1000 (3) failed acpi0: reservation of ffb80000, 80000 (3) failed acpi0: reservation of fec10000, 20 (3) failed acpi0: reservation of fed80000, 1000 (3) failed acpi0: reservation of 0, a0000 (3) failed acpi0: reservation of 100000, d7f00000 (3) failed cpu0: <ACPI CPU> on acpi0 cpu1: <ACPI CPU> on acpi0 attimer0: <AT timer> port 0x40-0x43 irq 0 on acpi0 Timecounter "i8254" frequency 1193182 Hz quality 0 Event timer "i8254" frequency 1193182 Hz quality 100 atrtc0: <AT realtime clock> port 0x70-0x71 irq 8 on acpi0 Event timer "RTC" frequency 32768 Hz quality 0 hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on acpi0 Timecounter "HPET" frequency 14318180 Hz quality 950 Event timer "HPET" frequency 14318180 Hz quality 550 Event timer "HPET1" frequency 14318180 Hz quality 450 Timecounter "ACPI-safe" frequency 3579545 Hz quality 850 acpi_timer0: <32-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0 pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 pci0: <ACPI PCI bus> on pcib0 pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0 pci1: <ACPI PCI bus> on pcib1 vgapci0: <VGA-compatible display> port 0xe000-0xe0ff mem 0xf0000000-0xf7ffffff,0xfe8f0000-0xfe8fffff,0xfe700000-0xfe7fffff irq 18 at device 5.0 on pci1 pcib2: <ACPI PCI-PCI bridge> irq 18 at device 6.0 on pci0 pci2: <ACPI PCI bus> on pcib2 bge0: <HP NC107i PCIe Gigabit Server Adapter, ASIC rev. 0x5784100> mem 0xfe9f0000-0xfe9fffff irq 18 at device 0.0 on pci2 bge0: CHIP ID 0x05784100; ASIC REV 0x5784; CHIP REV 0x57841; PCI-E miibus0: <MII bus> on bge0 brgphy0: <BCM5784 10/100/1000baseT PHY> PHY 1 on miibus0 brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto, auto-flow bge0: Ethernet address: XX:XX:XX:XX:XX:XX ahci0: <ATI IXP700 AHCI SATA controller> port 0xd000-0xd007,0xc000-0xc003,0xb000-0xb007,0xa000-0xa003,0x9000-0x900f mem 0xfe6ffc00-0xfe6fffff irq 19 at device 17.0 on pci0 ahci0: AHCI v1.20 with 4 3Gbps ports, Port Multiplier supported ahcich0: <AHCI channel> at channel 0 on ahci0 ahcich1: <AHCI channel> at channel 1 on ahci0 ahcich2: <AHCI channel> at channel 2 on ahci0 ahcich3: <AHCI channel> at channel 3 on ahci0 ohci0: <AMD SB7x0/SB8x0/SB9x0 USB controller> mem 0xfe6fe000-0xfe6fefff irq 18 at device 18.0 on pci0 usbus0 on ohci0 ehci0: <AMD SB7x0/SB8x0/SB9x0 USB 2.0 controller> mem 0xfe6ff800-0xfe6ff8ff irq 17 at device 18.2 on pci0 usbus1: EHCI version 1.0 usbus1 on ehci0 ohci1: <AMD SB7x0/SB8x0/SB9x0 USB controller> mem 0xfe6fd000-0xfe6fdfff irq 18 at device 19.0 on pci0 usbus2 on ohci1 ehci1: <AMD SB7x0/SB8x0/SB9x0 USB 2.0 controller> mem 0xfe6ff400-0xfe6ff4ff irq 17 at device 19.2 on pci0 usbus3: EHCI version 1.0 usbus3 on ehci1 pci0: <serial bus, SMBus> at device 20.0 (no driver attached) atapci0: <ATI IXP700/800 UDMA133 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xff00-0xff0f at device 20.1 on pci0 ata0: <ATA channel> at channel 0 on atapci0 ata1: <ATA channel> at channel 1 on atapci0 isab0: <PCI-ISA bridge> at device 20.3 on pci0 isa0: <ISA bus> on isab0 pcib3: <ACPI PCI-PCI bridge> at device 20.4 on pci0 pci3: <ACPI PCI bus> on pcib3 ohci2: <AMD SB7x0/SB8x0/SB9x0 USB controller> mem 0xfe6fc000-0xfe6fcfff irq 18 at device 22.0 on pci0 usbus4 on ohci2 ehci2: <AMD SB7x0/SB8x0/SB9x0 USB 2.0 controller> mem 0xfe6ff000-0xfe6ff0ff irq 17 at device 22.2 on pci0 usbus5: EHCI version 1.0 usbus5 on ehci2 acpi_button0: <Power Button> on acpi0 sc0: <System console> at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x300> vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 ppc0: cannot reserve I/O port range ctl: CAM Target Layer loaded acpi_throttle0: <ACPI CPU Throttling> on cpu0 hwpstate0: <Cool`n'Quiet 2.0> on cpu0 Timecounters tick every 1.000 msec usbus0: 12Mbps Full Speed USB v1.0 usbus1: 480Mbps High Speed USB v2.0 usbus2: 12Mbps Full Speed USB v1.0 usbus3: 480Mbps High Speed USB v2.0 usbus4: 12Mbps Full Speed USB v1.0 usbus5: 480Mbps High Speed USB v2.0 ugen0.1: <ATI> at usbus0 uhub0: <ATI OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus0 ugen1.1: <ATI> at usbus1 uhub1: <ATI EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus1 ugen2.1: <ATI> at usbus2 uhub2: <ATI OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus2 ugen3.1: <ATI> at usbus3 uhub3: <ATI EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus3 ugen4.1: <ATI> at usbus4 uhub4: <ATI OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus4 ugen5.1: <ATI> at usbus5 uhub5: <ATI EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus5 uhub4: 4 ports with 4 removable, self powered uhub0: 5 ports with 5 removable, self powered uhub2: 5 ports with 5 removable, self powered uhub5: 4 ports with 4 removable, self powered uhub1: 5 ports with 5 removable, self powered uhub3: 5 ports with 5 removable, self powered ada0 at ahcich0 bus 0 scbus0 target 0 lun 0 ada0: <WDC WD30EZRX-00DC0B0 80.00A80> ATA-9 SATA 3.x device ada0: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 8192bytes) ada0: Command Queueing enabled ada0: 2861588MB (5860533168 512 byte sectors: 16H 63S/T 16383C) ada0: Previously was known as ad4 ada1 at ahcich1 bus 0 scbus1 target 0 lun 0 ada1: <WDC WD30EZRX-00DC0B0 80.00A80> ATA-9 SATA 3.x device ada1: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 8192bytes) ada1: Command Queueing enabled ada1: 2861588MB (5860533168 512 byte sectors: 16H 63S/T 16383C) ada1: Previously was known as ad6 ada2 at ahcich2 bus 0 scbus2 target 0 lun 0 ada2: <WDC WD30EZRX-00DC0B0 80.00A80> ATA-9 SATA 3.x device ada2: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 8192bytes) ada2: Command Queueing enabled ada2: 2861588MB (5860533168 512 byte sectors: 16H 63S/T 16383C) ada2: Previously was known as ad8 ada3 at ahcich3 bus 0 scbus3 target 0 lun 0 ada3: <WDC WD30EZRX-00DC0B0 80.00A80> ATA-9 SATA 3.x device ada3: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 8192bytes) ada3: Command Queueing enabled ada3: 2861588MB (5860533168 512 byte sectors: 16H 63S/T 16383C) ada3: Previously was known as ad10 ada4 at ata0 bus 0 scbus4 target 1 lun 0 ada4: <INTEL SSDSC2CT120A3 300i> ATA-9 SATA 2.x device ada4: 150.000MB/s transfers (SATA, UDMA6, PIO 8192bytes) ada4: 114473MB (234441648 512 byte sectors: 16H 63S/T 16383C) ada4: Previously was known as ad1 SMP: AP CPU #1 Launched! Timecounter "TSC-low" frequency 11699577 Hz quality 800 Trying to mount root from ufs:/dev/ad1p2 [rw,noatime]... ZFS filesystem version 5 ZFS storage pool version 28